evaluation board user guide ug - 521 one technology way ? p. o . box 9106 ? norwood, ma 02062 - 9106, u.s.a. ? tel: 781.329.4700 ? fax: 781.461.3113 ? www.analog.com evaluating the cn - 0285 wideband tx modulator solution please see the last page for an important warning and legal terms and conditions . rev. 0 | page 1 of 8 features self - contained board including adf4351 w ideband pll + vco ADL5375 w ideband iq m odulator ultra low noise voltage regulators : adp150 , adp3334 25 mhz tcxo r eference usb interface accompanying adf4351 s oftware allows c ontrol of synthesizer f unctions from pc online resources documents needed adf4351 data sheet ADL5375 data sheet adp150 data sheet adp3334 data sheet required software adf435x programming software design and integration files schematics, layout files, bill of materials equipment needed a standard pc running windows? xp, windows vista (32 - bit), or windows 7 with a usb port eval - cn0285 - eb1z circuit evaluation board 5.5 v power supplies an i q signal source, such as the rohde & schwarz amiq a spectrum analyzer, such as the rohde & schwarz fsq8 general description the e va l - cn0285 - eb1z is the evaluation board described in the circuit s from the lab ? circuit note cn -0 285, broadband low evm direct conversion transmitter . a photo of the board is shown in figure 1 . it contains the adf4351 synthesizer, the ADL5375 wideband transmit modulator , and ultralow noise ldos. the board can be controlled using the adf4351 programming software. a usb cable is included with the board to connect to a pc usb port. additional information , including other pll data sheets, technical notes, articles, and adi s impll? pll simulation software from analog devices, inc. , is available at www.analog.com/pll . photo of the evaluation board figure 1. eval - cn0285 - eb1z 1 1267-001
ug-521 evaluation board user guide rev. 0 | page 2 of 8 table of contents features .............................................................................................. 1 online resources .............................................................................. 1 equipment needed ........................................................................... 1 general desc ription ......................................................................... 1 photo of the evaluation board .................................................... 1 revision history ............................................................................... 2 evaluation board hardware ............................................................ 3 powe r supplies ...............................................................................3 iq inputs .........................................................................................3 rf/lo outputs ..............................................................................3 loop filter and charge pump current ......................................3 reference source ...........................................................................3 evaluation board software qu ick start procedures .....................4 revision history 3 /1 3 rev ision 0: initial version
evaluation board user guide ug-521 rev. 0 | page 3 of 8 evaluation board har dware power supplies the user must apply 5.5 v to the v supply power connectors (4 mm banana connectors). an led, d6 , indicates when usb power is available, and another led, d5 , indicates when the main board is powered. switch sw - ext is used to switch in the 5.5 v supply. iq inputs the ADL5375 has four differential iq inputs. these are accessi - ble from the sma connectors and should be connected to an appropriate a nalog base b and iq source such as the rhode & schwarz amiq. set t he dc bias voltage for the iq inputs at 0.5 v. rf/lo outputs the ADL5375 rf output is ac - coupled out to the rfout sma. there are also two lo output sma connectors that can be used to view the filtered adf4351 rf outputs on a spectrum analy zer. when connecting to an analyz er, terminate the unused lo output with a 50 termination. when measuring evm or adjacent channel leakage current ( aclr ), disconnect these lo outputs by removing capacitors c72 and c73 to prevent loading the circuit. loop filter and charge pump current the loop filter schematic is included in the evaluation board and can be found at www.analog.com/cn0285-designsupport . the default loop filter is set to 70 khz . using a charge pump setting of 2.5 ma is recommended . figure 2. loop filter layout reference source the 25 mhz tcxo from rakon provides the necessary reference signal. an external refin can be used if desired. in this case, disable the on - board tcxo by removing r59. r9 can be populated with 50 ? to match the impedance of the evaluation board to the external reference source . 1 1267-002
ug-521 evaluation board user guide rev. 0 | page 4 of 8 evaluation board sof tware quick start pr ocedures the control software for e va l - cn0285 - eb1z uses th e standard adf4351 programming software. for more details on the installation of this software, consult ug - 435, evaluation board for the adf4351 frac tional - n pll frequency synthesizer . after installing the software, run the software by clicking the adi adf435x file on the desktop or in the start menu. the software front panel opens (see figure 3 ). confirm that analog devices rfg.l eval board connected is displayed in the bottom left corner of the window . otherwise, the software has no connection to the evaluation board. in this case , check that the cable connection and usb drivers are correctly installed. program the rf output frequency in the main controls tab of the software front panel. figure 3 . software front panel 1 1267-003
evaluation board user guide ug-521 rev. 0 | page 5 of 8 notes
ug-521 evaluation board user guide rev. 0 | page 6 of 8 notes
evaluation board user guide ug-521 rev. 0 | page 7 of 8 notes
ug-521 evaluation board user guide rev. 0 | page 8 of 8 notes esd caution esd (electrostatic discharge) sensitive device . charged devices and circuit boards can discharge without detection. although this product features patented or proprietary pr otection circuitry, damage may occur on devices subjected to high energy esd. therefore, proper esd precautions should be taken to avoid performance degradation or loss of functionality. legal terms and conditions by using the evaluation board discussed herein (together with any tools, components documentation or support materials, the evaluation board), you are agreeing to be bou nd by the terms and conditions set forth below (agreement) unless you have purchased the evaluation board, in which case the analog devices standard terms and conditions of sale shall govern. do not use the evaluation board until you have read and agreed to the agreement. your use of the evaluation board shall signify your acceptance of the agreement. this agreement is made by and between you (customer) and analog devices, inc. (adi), with its principal place of business at one technology way, norwoo d, ma 02062, usa. subject to the terms and conditions of the agreement, adi hereby grants to customer a free, limited, person al, temporary, non - exclusive, non - sublicensable, non - transferable license to use the evaluation board for evaluation purposes only. customer understands and agrees that the evaluation board is provided for the sole and exclusive purpose referenced above, and agrees not to use the evaluation board for any other purpose. furthe rmore, the license granted is expressly made subject to the following additional limitations: customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the evaluation bo ard; and (ii) permit any third party to access the evaluation board. as used herein, the term third party in cludes any entity other than adi, customer, their employees, affiliates and in - house consultants. the evaluation board is not sold to customer; all rights not expressly granted herein, including ownership of the evaluation board, are reserved by adi. confi dentiality. this agreement and the evaluation board shall all be considered the confidential and proprietary information of a di. customer may not disclose or transfer any portion of the evaluation board to any other party for any reason. upon discontinuati on of use of the evaluation board or termination of this agreement, customer agrees to promptly return the evaluation board to adi. additional restrictions. customer may not disassemble, decompile or reverse engi neer chips on the evaluation board. customer shall inform adi of any occurred damages or any modifications or alterations it makes to the evaluation board, including but not limited to soldering or any other activity that affects the material content of the evaluation board. modifications to the eva luation board must comply with applicable law, including but not limited to the rohs directive. termination. adi may terminat e this agreement at any time upon giving written notice to customer. customer agrees to return to adi the evaluation board at that time. limitation of liability. the evaluation board provided hereunder is provided as is and adi makes no warranties or representations of any kind with respect to it. adi specifically disclaims any representations, endorsements, g uarantees, or warrantie s, express or implied, related to the evaluation board including, but not limited to, the implied warranty of merchantability, title, fitness for a particul ar purpose or noninfringement of intellectual property rights. in no event will adi and its licensor s be liable for any incidental, special, indirect, or consequential damages resulting from customers possession or use of the evaluation board, including but not limited to lost profits, delay costs, labor costs or loss of goodwill. adis total li ability from any and all causes shall be limited to the amount of one hundred us dollars ($100.00). export. customer agrees that it will not directly or indirectly export the evalua tion board to another country, and that it will comply with all applicable united s tates federal laws and regulations relating to exports. governing law. this agreement shall be governed by and construed in accordance with the substantive laws of the commonwealth of massachusetts (excluding conflict of law rules). any legal action regar ding this agreement will be heard in the state or federal courts having jurisdiction in suffolk county, massachusetts, and cu stomer hereby submits to the personal jurisdiction and venue of such courts. the united nations convention on contracts for the int ernational sale of goods shall not apply to this agreement and is expressly disclaimed. ? 2013 analog devices, inc. all rights reserved. trademarks and registered trademarks are the property of their respective owners. ug11267 -0- 3 /13(0)
|
